Equipment › ANVER Vacuum Components › Vacuum Switches and Sensors › JTZSE digital control switch

ANVER JTZSE and JTZSE-R2 digital vacuum/pressure switches

The JTZSE and JTZSE-R2 are compact compound pressure gauges with switch outputs, eight operation modes and eight pressure units.

Vacuum system components
Digital vacuum/pressure control switches

Model JTZSE and model JTZSE-R2 digital control switches

JTZSE and JTZSE-R2 digital control switches

Model JTZSE digital control switch for non-corrosive gases
This popular model used for non-corrosive gases [compound and low pressure] is a compact multi-purpose compound pressure gauge, specifically designed to cover negative-to-normal pressure. A rear mount bracket option is available.

Model JTZSE-R2 digital control switch for liquids or gases
This special high corrosion resistant model [compound and absolute pressure] has pressure port attachments made of SUS 316L stainless steel for exact, accurate pressure control to cover a broad range of applications.

Features

  • Full 3-digit red LED display – gives a clear indication even in low light locations
  • Proven IP65 grade gauge body is suitable for industrial installations
  • Small, space-saving 30mm square face design
  • 2-point switch output with a total of eight operation modes possible
  • Analog output 1-5V in addition to the 2-point switch output
  • 8 different pressure units are available for selection

Digital vacuum/pressure control switch specifications

Model number

Pressure port

Diaphragm material

Net weight (including 2 m cable)

Accessories

JTZSE

Aluminum die-casting Rc 1/8 female, 2 places

Silicone, single crystal

2.928 oz. (83 grams)

Unit seal, seal screw, M5 connecting joint screw

JTZSE-R2

Mounting: R 1/4, with M5 female

SUS316L

5.291 oz. (150 grams)

Unit seal

Pressure reference: gauge – pressure setting range

Model number

Rated pressure range

kPa

gf/cm²

mmHg

mbar

psi

Breakdown pressure

JTZSE

-100 to 1000 kPa

-999 to 999

-999 to 999

-760 to 760

n/a

-14.5 to 14.5

500 kPa

JTZSE-R2

-100 to 100 kPa

-99.9 to 99.9

-999 to 999

-760 to 760

-999 to 999

-14.5 to 14.5

300 kPa

Switch output

Model number

General specifications

Hysteresis

Repeatability

Response

Short circuit protection

JTZSE

2-point output, NPN/PNP transistor open collector, capacity: 30 V DC 100 mA max., residual voltage: 1.2 V or below (at load current of 100 mA)

0 – 300 digits (adjustable)

+/- 0.2% F. S. +/- 1 digit

5 ms maximum

Provided

JTZSE-R2

Output mode setting (detected pressure – pin)

Model number

Output mode

R mode

G mode

V mode

Output voltage Vo

JTZSE

Pin (H)

+Pr

-Pr

-Pr

Vo(H)

JTZSE-R2

Pin (L)

-Pr

O

O

Vo(L)

Environmental characteristics

Model number

Protection grade

Operating temp. range

Storage temp. range

Operating humidity

Insulation resistance

Dielectric strength

Vibration

Shock

JTZSE

IP65 (Pressure Gauge Body): Conforming to IEC

14° to 122°F (-10 to 50°C)

68° to 158°F (20° to 70°C)

35 to 85% Relative Humidity

More than 100 M ohm at DC 500 V between wire bundle and pressure port

One minute at AC 500 V between wire bundle and pressure port (leak current: less than 1 mA)

10-55 Hz, amplitude 0.75 mm, 3 directions, 2 h each

+/-3% F.S. (0 ± 50°C)

JTZSE-R2

General

Model number

Analog output

Display

Negative pressure display

Switch state indication

JTZSE

Output voltage: 1-5 V (zero point 1 V ± 0.2 V, span 4 V ± 0.2 V)
Output Impedance: 10k ohm
Resolution: 1/204

Full 3 digit LED (Sampling Cycle: 4/second)

Negative Pressure LED is on

Output 1 (green) and output 2 (red) light up when output is on: Thermal Error

JTZSE-R2

Digital control switch dimensional drawing

Need an ANVER system for your load?

Send photos, weight and dimensions of the load. FullSharp represents ANVER and replies with a configuration and quote within 24 hours.

Contact us