Equipment › ANVER Vacuum Components › Vacuum Switches and Sensors › JTZSE4 digital control switch

ANVER JTZSE4 digital vacuum control switch

The JTZSE4 is a popular standard model, a compact compound pressure gauge covering negative to normal pressure.

Vacuum system components
Digital vacuum/pressure control switches

Model number JTZSE4 digital control switch for non-corrosive gases

JTZSE4 digital control switch

The JTZSE4 Digital Control Switch is a popular standard model for use with non-corrosive gases [compound and low pressure]. It is a compact multi-purpose compound pressure gauge specifically designed to cover negative to normal pressure. A rear mount bracket option is available.

Features

  • Full 3-digit red LED display – gives a clear indication even in low light locations
  • Proven IP65 grade gauge body is suitable for industrial installations
  • Small, space-saving 30mm square face design
  • 2-point switch output with a total of eight operation modes possible
  • Analog output 1-5V in addition to the 2-point switch output
  • 8 different pressure units are available for selection

Digital vacuum/pressure control switch specifications for JTZSE4

Sensor typeVacuum pressure 101 kPa type
Type of pressureGauge pressure
Rated pressure range0 to -101.3 kPa
Set pressure range5.1 to -101.3 kPa
Maximum pressure rating490kPa
Applicable fluidNon-corrosive gas
Selectable unitskgf/cm2, bar, psi, mmHg, inHg
Supply voltage12 to 24V DC, ripple P-P 10% or less
Current consumption50mA or less
Comparative outputs
Comparative output 1
Comparative output 2
Standard PNP output
PNP open-collector transistor
• Maximum source current: 100mA
• Applied voltage: 30V DC or less (between comparative output and +V)
• Residual voltage: 2V or less (at 100mA source current)
Output modesEquipped with 4 types of modes: hysteresis mode,
window comparator mode, dual output mode,
automatic sensitivity setting mode (selectable by key operation)
Hysteresis1 digit (variable in hysteresis mode and 2 digits when using psi unit)
RepeatabilityWithin ±0.2% F.S. ±1 digit
Response time2.5ms or less
Short-circuit protection incorporated
Analog voltage output

Output impedance: approx. 1 kΩ

Output voltage: 1 to 5V (over rated-pressure range)
Zero-point: within 1V ±5% F.S.
Span: within 4V ±5% F.S.
Linearity: within ± 1% F.S.
Display3½ digit red LED display (sampling rate: approx. 4 times/sec.)
Displayable pressure range5.1 to -101.3 kPa
Analog bar displayLED bar display in steps of approx. 10% F.S.
Operation indicators
Comparative output 1
Comparative output 2
Orange LED (lights up when Comparative Output 1 is ON)
Green LED (lights up when Comparative Output 2 is ON)
ProtectionIP40 (IEC)
Ambient temperature-10 to +50°C (no dew condensation or icing allowed). Storage: -10 to +60°C
Ambient humidity35 to 85% RH. Storage: 35 to 85% RH
Temperature characteristicsOver ambient temperature range -10 to +50°C: within ± 1% F.S. of detected pressure at 20°C
Pressure portNPTF 1/8 female thread
materialFront case: ABS • Rear case: PPS (glass fiber reinforced)
Display surface: Acrylic • Pressure port attachment: Die-cast zinc alloy
Cable0.15mm² 5-core oil-resistant cabtyre cable, 2m long
Cable extensionExtension up to a total of 100 m is possible with 0.3 mm² or larger cable
Weight3.351 oz. (95 grams)
AccessoriesOne (1) hexagon-socket-head plug for pressure port

Digital control switch dimensional drawing

Need an ANVER system for your load?

Send photos, weight and dimensions of the load. FullSharp represents ANVER and replies with a configuration and quote within 24 hours.

Contact us