Vietnam+84 332 839 268 Taiwan+886 3 451 8806 Send requestreply in 24 h

FullSharp · since 1991

Equipment › Ergonomic Vacuum Lifting Systems › ANVER VT Systems › VT Accessories and Parts › Vacuum pump motor starters

ANVER motor starters and transformers for vacuum pumps

ANVER motor starters combine short circuit protection, overload protection and switching in one compact unit, and each now comes with an enclosure.

Request a quote

Electric vacuum pump station accessories
Motor starters and protectors for vacuum pumps

ANVER motor starters for vacuum pumps

ANVER motor starters are made to the highest quality standards. The motor circuit controller combines the function of:

Short circuit protection
Current overload protection
Switching
3 phase

Manual starter

ANVER starters can eliminate the need for larger and more expensive fuse blocks and fused disconnects, or circuit breakers.

ANVER starters offer a wide application range, from 0.1 to 25 Full Load Amp (FLA). For group motor applications, ANVER starters have a group installation rating of up to 600V @ 2,000 Amp, one of the highest in the industry.

ANVER starters are also excellent as manual motor starters that employ all of the same motor protection features in one compact unit. ANVER starters are the most compact on the market today.

In the event of a short-circuit, the contacts are opened by non-adjusting tripping elements in times approaching 1/1000 of a second.

Because each ANVER starter is individually calibrated at the factory for the smallest and largest current, very accurate thermal overload protection is also obtained. Each motor starter now comes with an enclosure.

Motor starter specifications:

Horsepower ratings shown in the table below are for reference. The final selection of the manual starter depends on the actual motor full load current and service factor.

ANVER part no.	Amperage range		Phase	Item weight lb (kg)	Maximum HP
ANVER part no.	Minimum	Maximum	Phase	Item weight lb (kg)	230V	460V	575V
ST-025-040	2.50	4.00	Three	N/A	3/4	2	3
ST-040-063	4.00	6.29	Three	1.66 (0.75)	1½	3	5
ST-063-100	6.30	9.99	Three	N/A	3	5	7½
ST-100-160	10.00	15.99	Three	1.66 (0.75)	5	10	10

Appropriate motor starters for ANVER vacuum pumps:

ANVER pump no.	HP	Recommended starter no.	Voltage	Amps	Port size	Hose in. (mm)
VB4HF	4.6 HP	ST-100-160	208-230	12.6	2″ NPT	2 (50.8)
		ST-063-100	460	7.3
		ST-040-063	575	5
VB7HV	4.8 HP	ST-100-160	208-230	10.3	1-1/4″NPT	2 (50.8)
		ST-063-100	460	5.0
		ST-025-040	575	3.9
VB8HF	8.5 HP	ST-200-250	208-230	24	2″ NPT	2 (50.8)
		ST-100-160	460	12
		ST-100-160	575	8.5
VB9HV	7.5 HP	ST-160-200	208-230	16.4	1-1/4″NPT	2 (50.8)
		ST-063-100	460	9.5
		ST-040-063	575	5.4

Electrical transformers for vacuum generators:

Model number

Unit weight

Used with generator

Incoming primary voltage

Outgoing secondary voltage

Wattage

A Depth

B Width

C Height

D Top holes

E Bottom holes

F Distance from top to bottom holes

Item weight lb (kg)

VLT-01

30 lbs
14 kg

VPE1 VPF-57

240V, 480V 60Hz

120V 60Hz

1.5KVA

5.2 in. 132 mm

5.5 in. 140 mm

10.3 in. 262 mm

1.4 in. 36 mm

2.4 in. 61 mm

11.6 in. 295 mm

N/A

VLT-03

38 lbs
17 kg

VPE3

240V, 480V 60Hz

120V 60Hz

2KVA

4.5 in. 114 mm

4.8 in. 122 mm

11.8 in. 300 mm

1.4 in. 36 mm

2.1 in. 53 mm

13.0 in. 330 mm

N/A

VLT-06

30 lbs
14 kg

VPE1 VPF-57

600V 60Hz

120V 60Hz

1.5KVA

5.2 in. 132 mm

5.5 in. 140 mm

10.3 in. 262 mm

1.4 in. 36 mm

2.4 in. 61 mm

11.6 in. 295 mm

N/A

VLT-14
(export model)

38 lbs
17 kg

VPE1 VPF-57 VPE3

190V, 200V 208V, 380V 400V, 416V 50/60Hz

120V 50/60Hz

2KVA

5.2 in. 132 mm

5.5 in. 140 mm

13 in. 330 mm

1.4 in. 36 mm

2.1 in. 53 mm

13.5 in. 343 mm

3.81 (1.73)

Transformers should be remote mounted

**Other voltages / phases available: Generators can be supplied in the following voltages by adding a transformer: 208V, 220V, 230V, 380V, 440V, 460V, 480V, 575V (consult us for more information). All generator motors with a voltage of 120V or less use fuses or circuit breakers for protection. Motors and other devices that use more than 200V are fused and/or use thermal overload with a contactor.
Transformers should be remote mounted: Increasingly many local regulations require you not to have 3 phase power running below the hook. This is usually the case with smaller units which are intended to be used by an operator. The transformer should thus be wall or remotely mounted for safety. The proper transformers for the lifters ship separately in a box and need to be installed by a qualified electrician. It is usually best to contract this to a local crane installer or electrician familiar with the local code requirements.

Note: All ANVER electrical components, controls and wiring follow international standards: UL, CSA, NFPA, NEC. It is the user’s responsibility to comply with all additional local electrical codes as they pertain to the installation.
Important: The ASME B30.20 regulations, which are the American standard (ASME website) state this about “(i) Power disconnects.
(1) Hoisting Equipment using an externally powered vacuum lifter shall have a separate vacuum lifter circuit switch of the enclosed type with provision for locking, flagging, or tagging in the open (off) position. The vacuum lifter disconnect switch shall be connected on the line side (power supply side) of the hoisting equipment disconnect switch. (2) Disconnects are not required on externally powered vacuum lifters operating a 120 VAC single phase power source.”

Replacement Lift Tube Sets Lift Tubes and Tube Covers Top Swivel Assemblies Bottom Swivels and Quick Releases HP Series Vacuum Hose FLT Vacuum Filters Vacuum and Pressure Gauges VRV Vacuum Relief Valves Regenerative vacuum stations Bag Head Pad Attachments PGA-B150-NEO pistol grip pad VT-GHF hook foot

Need an ANVER system for your load?

Send photos, weight and dimensions of the load. FullSharp represents ANVER and replies with a configuration and quote within 24 hours.

ANVER motor starters and transformers for vacuum pumps

Related pages

Need an ANVER system for your load?