Vietnam+84 332 839 268 Taiwan+886 3 451 8806 Send requestreply in 24 h

VN EN TW

FullSharp · since 1991

Servo tractors

Name: Servo tractors
Brand: FullSharp

Overview

Knight servo tractors use IAD servo technology to move and stop loads at programmed positions on an overhead rail while lifting, cutting operator push/pull forces.

Knight’s Servo Tractors are designed to accurately locate, push, tow, lift and position loads from an overhead rail system. Tractors significantly reduce the push/pull forces as well as the energy to sustain movements.

These Servo Tractors are equipped with Knight’s (IAD) Intelligent Assist Device Servo Technology, allowing them to provide controlled transfers of workloads with speed and precision. They can be programmed to automatically or manually move and stop the runway at intended locations with repeatable accuracy while lifting loads at the same time; thus eliminating unnecessary operator motions. They can also be programmed for assembly line speed synchronization.

The KST4000 Rack and Pinion Servo Tractor offers a continuous contact non-slip rack and pinion design. This continuous non-slip design allows for a more accurate positioning of the load. Movement of the Servo Tractor is controlled by a two speed pendant, and can be programmed for multiple positions.

General Information

Mechanical

Variable Maximum Speed: Up to 174 ft. per min. [53.2mpm].
Maximum Towing Capacity: Up to 4,000 lbs. [1,814.37kg].
Maximum Lifting Capacity: Up to 1,000 lbs. [453.59kg].
Non-Slip Rack and Pinion Drive System.
Clutch (24 VDC).
Power and Free Drive Wheel.
Absolute Positioning.
Safety Rating of 125%.
Fail Safe Brake.
Knight’s Patented Chain, for longer life.
Chain Lengths, Unlimited (18 ft. Standard).
Sealed Worm Style Gearbox.

Software

Programming and Diagnostic Communication Ports.
Virtual Travel Limits.
Speed Reduction Zones.
Impact Limiting.
Active Dampening.
Standard Float Mode.
Programmable Overload Capability.

Electrical

Industry Standard 24 VDC, 2 AMP power is available for custom tooling such as: Clamps, Vacuum Cups, Switches, Proximity Limits, Lights, etc.
H5 Rated (Continuous Duty Cycle).
240VAC, Single Phase, 50/60 Hz.
Load Sensing, Pay Load and Handle Load.
I/O Capabilities:
– (16) Inputs/ (8) Outputs
– (8) Inputs/ (4) Outputs are free for interface controls.
LED Status Indicators, Green and Blue Lighted Push buttons.
LED Fault Indicators, Illuminated Run/ Stop Button, Twist to Release.
Optional Remote Pendant or Wireless Remote Control.

Axis Direction Options

Rack and Pinion Tractor
“X” Tractor w/”Z” Control
“X/Y” Tractor
“X/Y” Tractor w/”Z” Control
“XX/Y” Tractor w/”Z” Control

Servo Tractor Series Specifications

KST4000 Rack and Pinion Tractor Series

Towing Capacity lbs. [kg]	Max. Speed [fpm/mpm]
4,000 [1,814.37]	261.8 fpm. [79mpm]
4,000 [1,814.37]	174.53 fpm. [53.2mpm]

KSHXZ/ KSHXY/ KSHXYZ/ KSHXXYZ Servo Tractor Series

Hoist Capacity lbs. [kg]	Towing Capacity lbs. [kg]	Hoist Lift Speed [fpm.]	Tractor Travel Speed [fpm.]
250 lbs. [113.40kg]	4,000 lbs. [1,814.37kg]	196.85 fpm. [60.0mpm]	174.53 fpm. [53.2mpm]
350 lbs. [158.75kg]	4,000 lbs. [1,814.37kg]	241.00 fpm. [73.5mpm]	174.53 fpm. [53.2mpm]
750 lbs. [340.19kg]	4,000 lbs. [1,814.37kg]	123.03 fpm. [37.5mpm]	174.53 fpm. [53.2mpm]
1,000 lbs. [453.59kg]	4,000 lbs. [1,814.37kg]	82.02 fpm. [25.0mpm]	174.53 fpm. [53.2mpm]

Videos

*Applications Compilation

*Servo Hoist XYZ System – Seat Install

*XY Servo System – Lift Gate

*XYZ Servo System – IP Install

Automated Servo – Transfer Case Lift Assist

Servo Hoist and Tractor Engine Lift Assist

Servo Hoist and Tractor Engine Transfer

Accessories

Servo Controls 8

EPDA9600Two-Speed Control Handle

Weight: 2.5 lbs. [1.13 kg]

Details

The EPDA9600 Two-Speed Control Handle is a non-programmable handle. It is comprised of four switches to make up a (2) two-speed operation by simply compressing the thumb levers. Halfway is one speed, fully compressed is the second speed. Units come with a standard mounting flange. You will need to specify the flange adaptor tube size for your End Effector. Non-Programmable Handle.

Previously KCA1030

Non-Programmable Handle.
Various Mounting Options.
May be mounted remotely from the end effector.
(2) Thumb Lever Configuration.
(2) Switches per thumb lever.
(4) Single Pole 240V, 3A Limit Switches.
Switches IP67.
UL Listed, CE Approved.
Cables – M12 4-pin female mating cables sold separately.
BPD1125 Ergo Grip.
Strain Cable / Tether per application use.
Specify Mounting Collar Size: (.88 in., 1 in., 1.25 in.).
Optional EPA9600 Single Speed Control Handle.
Optional EPTA9600 Single Speed Control Handle with Trigger.
Optional EPDTA9600 Two-Speed Control Handle with Trigger.
Optional Color-Coded Thumb Levers.
Optional Angled Thumb Levers.
Custom lever markings, specify when ordering.
Different Call-out Languages Available.

CAD drawing

Two-Speed Control Handle with Trigger EPDTA9600

EPDTA9600Two-Speed Control Handle with Trigger

Weight: 2.8 lbs [1.27 kg]

Details

The EPDTA9600 Two-Speed Control Handle w/ Trigger is a non-programmable handle. It is comprised of five switches to make up a (2) two-speed operation with Trigger Button by simply compressing the thumb levers. Halfway is one speed, fully compressed is the second speed. Units come with a standard mounting flange. You will need to specify the flange adaptor tube size for your End Effector.

Non-Programmable Handle.
May be mounted remotely from the end effector.
(1) Switch trigger lever.
(2) Thumb Lever Configuration.
(2) Switches per thumb lever.
(1) trigger lever.
BPD1125 Ergo Grip.
(5) Single Pole 240V, 3A Limit Switches.
Switches IP67.
UL Listed, CE Approved.
Various Mounting Options.
Cables – M12 4-pin female mating cables sold separately.
Strain Cable / Tether per application use.
Specify Mounting Collar Size: (.88 in., 1 in., 1.25 in.).
Optional EPA9600 Single Speed Control Handle.
Optional EPTA9600 Single Speed Control Handle with Trigger.
Optional EPDTA9600 Two-Speed Control Handle with Trigger.
Optional Color-Coded Thumb Levers.
Optional Angled Thumb Levers.
Custom lever markings, specify when ordering.
Different Call-out Languages Available.

CAD drawing

Wireless Remote Control KCA1004 / KCA1005 / KCA1006

KCA1004 / KCA1005 / KCA1006Wireless Remote Control

Weight: Varies

Details

The KCA1004, KCA1005 and KCA1006 Wireless Remotes by Enrange FLEX® are used to control Knight Servo Systems where wireless control is preferred. They are set-up and programmed to simulate the control functionality of a remote pendant control handle. Each wireless system consists of (1) one transmitter handset and (1) one receiver unit. Other standard-equipped accessories include a transmitter belt, spare transmitter power key, clear vinyl pouch and "AA" alkaline batteries.

The Wireless Remotes are available with up to (8) eight programmable operation/ function push-buttons (As Shown). Float, Lift, UP and DOWN are standard push-button configurations. Wireless signal distance is good up to 900 ft. [300m].

Full Compliance: All systems are fully compliant with the FCC Part-15 Rules, European Directives (Safety, EMC, R&TTE, Machinery), and Industry Canada Specifications (IC).

(Previously EBA1054)

Wireless Remote.
Wireless Signal: Up to 900 ft. [300m].
Ultra-Durable Nylon and Fiberglass Composite Enclosures.
Up to (8) Eight Function/ Operation Buttons.
(62) User-Programmable Channels.
Automatic Channel Scanning Receiver.
32bit CRC and Hamming Codes.
Reliable Push-Buttons. – Rated for more than one million press cycles.
Power Consumption: (2) “AA” Batteries, 100 hours plus.
Durable Construction.
Compact and Lightweight.
Custom Push-Button Labels.
Improves Material Handling Operations.
Low Power Consumption.
KCA1004 – (4) Button.
KCA1005 – (6) Button
KCA1006 – (8) Button.

CAD drawing

Two-Speed Control Handle with Operator Control Interface KCA1033

KCA1033Two-Speed Control Handle with Operator Control Interface

Weight: 5.04 lbs. [2.29 kg]

Details

The KCA1033 is a Base Pendant Control for a Knight Servo Hoist. It permits the operator to control over-sized or cumbersome loads while maneuvering them into tight spaces. Control Handle is equipped with the same features as the Knight Inline Trigger Control Handle and is available in a Single or Two-Speed configuration that may be mounted on a separate cable, connected to a Knight (LMM) Load Monitoring Module or connected directly to a Servo Hoist box.

Knight Global's Operator Control Interface consists of (2) 4-Pin M12 female receptacles for I/O, (1) 6-Pin M12 receptacle for fixture handle, (1) 19-Pin male receptacle, Green/Blue lighted push buttons, lighted Red Run-Stop Push Button and (1) 9-Pin programming port.

(**Previously EBA1063)

Allows for 2-Speed Operation.
Operator Control Interface (OCI).
9-Pin D-Sub Programming Port.
19-Pin I/O and Control Connector.
Safety Run-Stop Button.
Illuminated (Blue/Green) Float and Lift Push Buttons.
Electrical Straight Cable sold separately.
Electrical Coil Cable sold separately.
Optional Trigger Button Configuration.

CAD drawing

KCA1071Load Cell Fixture Handle

Weight: 10.9 lbs [4.96kg]

Details

The KCA1071 Load Cell Fixture Handle is a programmable load sensing handle that can be mounted inline or remotely on the system. The fixture handle offers an inherent intuitive motion. The operator places force on the handles which creates a directional motion for the overall system which eliminates the need to push buttons. Up and Down motions can be initiated by grasping anywhere on the fixture handles.

Knight's KCA1071 Load Cell Handles are designed for rugged applications and high duty cycles.

Previously EBA1141

Designed for rugged applications and continuous duty cycles.
Eliminates need to push buttons.
Motion initiated by simply grasping handles.
500 lbs. [226kg] Load Cell with Amplifier.
Attaches directly to fixture.
Load Responsive Handling.
Handle Force Response: – Less than 1.5 lbs. [0.68kg].
Handle Fixture Size: 5 X 5.
(1) 8-Pin M12 Male Receptacle.
(2) 6 in. [152mm] Handles Included. – (Unless Specified)
Custom handles can be configured for most applications and are designed on a per job basis.
8-pin M12 cable is included, length to be specified.

CAD drawing

Inline Control Handle with Trigger KLCA1000

KLCA1000Inline Control Handle with Trigger

Weight: 15 lbs. [6.81kg]

Details

The KLCA1000 incorporates the latest in design that includes our patented load cells with integral amplifier for noise immunity, connectors for operator interface and an improved clevis mount with cross pinning to eliminate the need for threaded rod, for connecting devices below the handle grip. The KLCA1000 is a programmable load sensing handle that mounts inline of the chain on the system. The inline handle offers an inherent intuitive motion.

The KLCA1000's actuation trigger prevents the system from any unintentional movement. The operator has to depress the trigger to initiate any up or down movement. The KLCA1000 is smaller in size and weight, which creates a more ergonomic operator condition. The trigger is a feather touch, so it requires very little force to actuate. New servo software code for the trigger enables the handle speed to change direction faster, requiring less force to move up and down.

The KLCA1000 Inline Control handle with Trigger has increased responsiveness, to meet the demands of high production rates with little effort.

The KLCA1000 handle top hat connects our 4mm KDSA1010 or 5mm KDSA1011 servo chain.

(Previously EBA1381)

(LMM) Load Monitoring Module.
(OCI) Operator Controlled Interface.
750 lb. Handle Load Cell.
(1) 19-Pin I/O Male Receptacle.
Up to: (4) 4-Pin M12 Female Receptacles for I/O.
(1) M12 4-Pin D-Coded Female Ethernet Receptacle.
Illuminated Blue/ Green Push Buttons.
Illuminated Red Run-Stop Button.
Electrical cables sold separately.
Shackle sold separately.
KLCA1000-750:
- System Capacity: 750 lbs. [340kg].
- 750 lbs. Inline Handle-Sourcing.
- 750 lb. Gross Load Cell.
KLCA1000-2000:
- System Capacity: 2,000 lbs. [907kg].
- 2,000 lbs. Inline Handle-Sourcing.
- 2,000 lb. Gross Load Cell.

CAD drawing

(LMM) Load Monitoring Module with OCI KLCA1002

KLCA1002(LMM) Load Monitoring Module with OCI

Details

Fully programmable analog style load monitoring module that incorporates the latest in designs. The KLCA1002 includes our patented load cells with integral amplifier for noise immunity, packaging to protect lights buttons and connectors from operator interface, and improved clevis mount with cross pinning to eliminate the need for threaded rod, for connecting devices below the handle grip.

The LMM programmable load sensing module mounts inline of the chain on the system and is used when the operator is able to reach the run stop button when the hoist is in the up position. The KLCA1002 is recommended when an Inline Control Handle is not a practical solution.

(**Previously EBA1165)

Used in conjunction with the Dual Speed Handle Pendant or Fixture Handle.
(OCI) Operator Controlled Interface.
Ethernet Programming Port.
Up to: (3) 4-Pin M12 Female Receptacles for I/O.
(1) 19-Pin M23 Male Receptacle.
(1) 6-Pin M12 Receptacle for Fixture Handle.
Illuminated Blue/ Green Push Buttons.
Illuminated Red Run-Stop Button.
KSAA1004 Shackle comes standard.

CAD drawing

(LMM) Load Monitoring Module with Pass Through KLCA1004

KLCA1004(LMM) Load Monitoring Module with Pass Through

Details

Fully programmable analog style load monitoring module that incorporates the latest in designs. The KLCA1004 includes our patented load cells with integral amplifier for noise immunity, packaging to protect lights buttons and connectors from operator interface, and improved clevis mount with cross pinning to eliminate the need for threaded rod, for connecting devices below the handle grip.

The LMM programmable load sensing module mounts inline of the chain on the system and is used when the operator is not able to reach the run stop button when the hoist is in the up position, and is used in conjunction with the KCA1015 (OCI) Operator Controlled Interface module.

KCA1040 Electrical Coil Cable and KCA1041 Electrical Straight Cable sold separately.

(Formerly EBA1166)

Ethernet Programming Port.
Used in conjunction with the Dual Speed Handle Pendant, Fixture Handle or remote OCI module.
(1) 19-Pin M23 Male Receptacle.
(1) 19-Pin M23 Female Receptacle.
KSAA1004 Shackle comes standard.

CAD drawing

General 6

ETA1045Gear Rack Installation Clamp

Details

Knight Global's ETA1045 Gear Rack Installation Clamp assists in the installation of the linear gear rack by holding the rack in position, tight to the bottom of the rail. It can also be used as a gauge, to splice two pieces of rack together for a perfect assembly process. Used with the Knight Servo Tractors.

Easy to use “T” handles.
Lock into Knight rail channel.
Quicker, easier and more accurate installation.

CAD drawing

Quick Connect/ Disconnect KSAA1001 / KSAA1002

KSAA1001 / KSAA1002Quick Connect/ Disconnect

Max capacity: KSAA1001: 1,500 lbs. [680kg] KSAA1002: 1,500 lbs. -2,000 lbs. [453.5kg-907kg]

Details

The KSAA1001 and KSAA1002 Quick Connect/Disconnects allow for fast connections and disconnections of fixtures and end effectors. The Quick Connect/ Disconnect easily disengages by the simple pull of a release pin. Each quick disconnect comes with two pins, and can be quickly connected to the servo inline handle.

KSAA1001 : 16mm to 7/8 in. adapter
KSAA1002 : 20mm to 1.25 in. adapter

(Previously EBA1183 / EBA1265)

Forged Alloy Steel – Quenched and Tempered.
Fast Tool Connections/ Disconnections.
Each disconnect comes with two male stems EBD1825-1, 5″x7/8″, custom stems available upon request.

CAD drawing

KSAA1004Shackle

Max capacity: 1,000 lbs. [453kg]

Details

Secures fixtures and loads in-line with the Servo System chain. The KSAA1004 Shackle is normally attached below the load cell. Knight's Shackle features a female clevis for direct connections. The KSAA1004 Shackles are constructed of 4140 steel, and heat treated to Rock "C" 38-42. They have (2) two M6 steel dowel pins to capture, verses threaded rod and a M5 cross hole with retaining plates. Shackle is normally attached below the load cell handle.

(Previously EBA1213)

4140 Steel Shackle Housing.
Secures fixtures or loads in-line with chain.
Shackle attaches to 16mm 4140 steel shaft (Not Included).
Shackle is secured with (2) steel dowels.
5/8 in. grade 8 shoulder bolt.
Throat Opening: 7/8 in. X 2-1/8 in.

CAD drawing

KSAA1007Swivel Hook Shackle

Max capacity: 1,000 lbs. [453kg]
Weight: 4.6 lbs [2.08kg]

Details

The KSAA1007 secures fixtures and loads in-line with the Servo System chain. This Shackle is designed with a larger connection opening to accommodate for Knight's KSAA1007 Swivel Hook width. The KSAA1007 Swivel Hook Shackle is normally attached below the load cell handle and is used primarily for Knight's In-Line Handle applications. Shackle is normally attached below the load cell handle and used primarily for in-line handle applications that utilize a KSAD1022 Swivel Hook.

(Previously EBA1269)

4140 Steel Shackle Housing.
Larger Connection Opening.
Secures fixtures or loads in-line with chain.
Shackle attaches to 16mm 4140 steel shaft (Not Included).
Shackle is secured with (1) steel dowel and (1) Steel Pin-bolt.
Includes KSAD1022 Swivel Hook with Eye.

CAD drawing

Precision Roller Chain Wear Gauge KSAA1063

KSAA1063Precision Roller Chain Wear Gauge

Details

The KSAA1063 Precision Chain Wear Gauge is used to measure the wear on Knight Servo Arm Roller Chains. It's easy to use and very precise in gauging the wear on the roller chains.

Measures Knight Double Strand ANSI 50-2 Roller Chain Wear.

CAD drawing

KSAD1022Swivel Hook with Eye

Max capacity: 3,200 lbs. [1,451kg]
Weight: 1.6 lbs. [.72kg]

Details

The KSAD1022 Swivel Hook has a latch that automatically closes when the load is applied and can only open by pressing the release button and removing the load. You load them up and their latch locks them down. The KSAD1022 Swivel Hook is a Supermax grade 100 hook that is 20% stronger then high strength (grade 80) hooks when used with chain of the same grade. This hook is included with the KSAA1007 Swivel Hook with Shackle. The SHUR-LOC® hook, if properly installed and locked, can be used for personnel lifting applications and meets the intent of OSHA Rule 1926.1431(g)(1)(i)(A) and 1926.1501(g)(4)(iv)(B). Use in corrosive environment requires shank and nut inspection in accordance with ASME B 30.10-1.10.4 (b)(5)(c) 2009.

Previously EBA1219

Forged Alloy Steel – Quenched and Tempered.
Included with KSAA1007 Swivel Hook with Shackle.
Swivel Hook utilizes anti-friction bearing design which allows hook to rotate freely under load.
Individually Proof Tested at 2-1/2 times the 4:1 Working Load Limit with certification.
Grade: 100.
Recessed trigger design is flush with the hook body, protecting the trigger from potential damage.
Positive Lock Latch is Self-Locking when hook is loaded.
Trigger – consists of spring, roll pin and trigger.
Hook swivel allows positioning and connecting loads easier
Open bend keeps the load inline with the chain.
Open bend allows for ease of engaging and disengaging the load.
Easy to operate with enlarged thumb access.
Rated for both Wire Rope and use with Grade 80/100 Chain.
Fatigue rated.

CAD drawing

Electrical Cables 4

CALL8-Pin Micro Switch Cable

Lengths: 1m [3.28 ft.] to 6.0m [19.68 ft.]

Details

8-Pin Micro Switch Load Cell Cables are a DC Single Key, AWM PVC Grey, 8x24 AWG, 105°C, 60 VAC/75VDC, 2 A, 7.3 mm OD, TPE, Male / Female, shielded Cord Assembly. They come in various lengths and are also available with either Straight or Right Angle connector ends.

8-Pin Micro DC Single Key.
PVC Gray.
90° Male / Female Connectors.
22 AWG, 4A, 300V Cord.
Available with Straight or Right Angle Connector Ends.

CALL4-pin Micro Switch Cable

Lengths: 1m [3.28 ft.] to 6.0m [19.68 ft.]

Details

4-Pin Micro Switch Load Cell Cables are a DC Single Key, AWM PVC Grey, 8x24 AWG, 105°C, 60 VAC/75VDC, 2 A, 7.3 mm OD, TPE, Male-In-Line/ Female, shielded Cord Assembly. They come in various lengths and are also available with either Straight or Right Angle connector ends.

4-Pin Micro DC Single Key.
PVC Gray.
Male-In-Line/ Female Connectors.
22 AWG, 4A, 300V Cord.
Available with Straight or Right Angle Connector Ends.

KCA1040Electrical Coiled Cable

Details

The KCA1040 Electrical Coil cable provides a robust method of communicating from the OCI (Operator Control Interface) module on the floor level, to the servo controls up on the rail. The coil cable is made up of a high resistant PVC and has proved the test of time. The four inch coil connects the In-Line Handle or (LMM) Load Monitoring Module in a clean and compact package by wrapping around the Servo Hoist Chain. The KCA1040 Coiled Cable is made exclusively for Knight with 19-Pin Military style connectors and is available in various cable lengths. Knight's KCA1040 coiled cable is provided in many lengths, with specified lengths being the total. For example a 3ft coil will stretch to 3ft. See product features for all part numbers.

Previously EBA1011

Electrical Coiled Cables are made exclusively for Knight Global.
Connects a Servo Hoist to a load monitoring module by wrapping itself around the Servo Chain.
19-Pin Military Bayonet Style Connectors.
90 Degree Male to Female Connectors.
Optional Straight Cable configuration.
Available Lengths:
- KCA1040-2 (2 ft. [60.9 cm])
- KCA1040-3 (3 ft. [91.4 cm])
- KCA1040-4 (4 ft. [121.9 cm])
- KCA1040-6 (2 ft. [182.9 cm])
- KCA1040-8 (8 ft. [243.8 cm])
- KCA1040-10 (10 ft. [304.8 cm])
- KCA1040-12 (12 ft. [365.7 cm])
- KCA1040-15 (15 ft. [457.2 cm])
- KCA1040-20 (20 ft. [609.6 cm])

KCA1041Electrical Straight Cable

Lengths: • KCA1041-2 ( 2 ft. [61.0 cm] ) • KCA1041-3 ( 3 ft. [91.4 cm] ) • KCA1041-4 ( 4 ft. [121.9 cm] ) • KCA1041-6 ( 6 ft. [182.9 cm] ) • KCA1041-10 ( 10 ft. [304.8 cm] ) • KCA1041-15 ( 15 ft. [457.2 cm] )

Details

The KCA1041 Electrical Straight cable provides a robust method of communicating from the OCI (Operator Control Interface) module to the LMM (Load monitoring Module). The cable is made up of a high resistant PVC and has proved the test of time. The straight cable connects the In-Line Handle or (LMM) Load Monitoring Module. The cable is made exclusively for Knight with 19-Pin Military style connectors and is available in various cable lengths.

Previously EBA1009

Electrical Straight Cables are made exclusively for Knight Global.
Connects a separate control handle pendant to Servo Hoists.
19-Pin Military Bayonet Style Connectors.
90 Degree Male to Female Connectors.
Optional Coiled Cable configuration.

Disconnects 9

7.5KVA Electrical Disconnect Enclosure EBA1289

EBA12897.5KVA Electrical Disconnect Enclosure

Details

The EBA1289 7.5 KVA Electrical Disconnect Enclosures converts 480VAC to 240VAC for powering the Knight Global servo hoists, this panel comes with an industrial flange disconnect and provides a means to lock out the system when time for maintenance. It also includes a 7.5KVA finger safe transformer, with primary and secondary fused disconnects. THE EBA1289 is used on applications with four servo tractor systems. (i.e., Knight's KSHXXYZ and KSHXYZR Servo Tractors Systems).

Used with: KSHXXYZ and KSHXYZR Servo Tractor Systems.
(2) Flange disconnect with (1) 480VAC and (1) 240VAC.
Transformer, 7.5 KVA.
Mounting plate and stand EBA1145.
480VAC – 240VAC, FLA 10.4.
25A Primary Fusing.
25A Secondary Fusing.
Enclosures are mounted at a ergonomically correct height.

Electrical Disconnect Enclosure Stand KCA1001

KCA1001Electrical Disconnect Enclosure Stand

Details

The KCA1001 Electrical Disconnect Enclosure Stand is for the mounting of disconnect enclosures to provide an ergonomically positioned height for the flange disconnect handle. Stand allows for multiple adjustment heights. Mounting patterns set up for Knight's KCA1018 and KCA1055 transformer disconnect enclosure boxes. Electrical Disconnect Enclosure Box Not Included.

Previously EBA1145

Provides mounting surface for enclosures in open workstation environments.
Stand allows for multiple adjustment heights.
Electrical Disconnect Enclosure Box Not Included.
Air Prep option for the back side.
Floor Mounted.
Bolted Construction M10X1.5 w/ Nylock nuts.
Various enclosures mount to stand.
Wall mounted enclosures mount to stand.
Custom finishes are available. (Blue is Standard).
Foot Print: 30x21x62.
Floor Mounting Hole Pattern: 24×18.
Optional Pneumatic Lockout Mounting Plate.
Optional Dual Enclosure Configuration. (Front and Back).

Electrical Disconnect Enclosure Stand KCA1002

KCA1002Electrical Disconnect Enclosure Stand

Details

The KCA1002 Electrical Disconnect Enclosure Stand is for the mounting of Power Distribution Panels (PDP) to provide an ergonomically positioned height for access. It is equipped with an over-sized lower cross brace for front side air prep. Stand allows for multiple adjustment heights. PDP Not Included.

Provides mounting surface for enclosures in open workstation environments.
Stand allows for multiple adjustment heights.
Power Distribution Panel (PDP) Not Included.
Air Prep option for the back side or the lower cross brace.
Floor Mounted.
Bolted Construction M10X1.5 w/ Nylock nuts.
Custom finishes are available. (Blue is Standard).
Foot Print: 40x21x65
Optional Pneumatic Lockout Mounting Plate.

Electrical Disconnect Enclosure Stand KCA1003

KCA1003Electrical Disconnect Enclosure Stand

Details

The KCA1003 Electrical Disconnect Enclosure Stand is for the mounting of a PDP (Power Distribution Panel) to provide an ergonomically positioned height for the flange disconnect handle. It is equipped with an over-sized cross brace for front and side air prep. It also features an additional side plate space used to mount ancillary controls such as a lighting disconnect. The stand allows for multiple adjustment heights. PDP Box Not Included.

Provides mounting surface for enclosures in open workstation environments.
Stand allows for multiple adjustment heights.
Power Distribution Panel (PDP) Not Included.
Air Prep option for the back side.
Floor Mounted.
Bolted Construction M10X1.5 w/ Nylock nuts.
Custom finishes are available. (Blue is Standard).
Foot Print: 56x21x66
Optional Pneumatic Lockout Mounting Plate.
Optional Dual Enclosure Configuration. (Front and Back).

3KVA Electrical Disconnect Enclosure KCA1018

KCA10183KVA Electrical Disconnect Enclosure

Details

The KCA1018 3KVA Electrical Disconnect Enclosures converts 480VAC to 240VAC for powering the Knight Global servo hoists. This panel comes with an industrial flange disconnect and provides a means to lock out the system when time for maintenance. It also includes a 3KVA finger safe transformer and primary and secondary fusing for all your single chain servo products. (i.e., Knight's KSH250S, KSH350S, KSH500S, KSH750S and KSH1000S Servo Hoists). Electrical Disconnect Enclosure Stands Not Included.

Previously EBA1003

Used with: KSH250S, KSH350S, KSH500S, KSH750S and KSH1000S Servo Hoists.
Flange disconnect.
Transformer Disconnect, 3KVA.
Enclosure Size: 21 in. X 20 in. X 10 in.
480VAC – 240VAC, FLA 6.25.
15A Primary Fusing.
15A Secondary Fusing.
Enclosures are mounted at a ergonomically correct height.
Optional Dual Enclosure Configuration. (Front and Back)
Stand not included.

5KVA Electrical Disconnect Enclosure KCA1055

KCA10555KVA Electrical Disconnect Enclosure

Details

The KCA1055 5KVA Electrical Disconnect Enclosures converts 480VAC to 240VAC for powering the Knight Global servo hoists. This panel comes with an industrial flange disconnect and provides a means to lock out the system when time for maintenance. It also includes a 5KVA finger safe transformer, primary and secondary fusing for your dual and triple servo products. (i.e., Knight KSHXY, KSHXZ, KSHTCDM, KSHXYZ Servo Tractors and Hoists). KCA1001 Electrical Disconnect Enclosure Stand Not Included.

Previously EBA1085

Used with: KSHXY, KSHXZ, KSHTCDM and KSHXYZ Servo Tractors and Hoists.
Flange disconnect.
Transformer Disconnect, 5KVA.
Enclosure Size: 30 in. X 25 in. X 12 in.
480VAC – 240VAC, FLA 10.4.
25A Primary Fusing.
25A Secondary Fusing.
Enclosures are mounted at a ergonomically correct height.
Optional Dual Enclosure Configuration. (Front and Back)
Stand not included.

Dual 5KVA Electrical Disconnect Enclosure KCA1056

KCA1056Dual 5KVA Electrical Disconnect Enclosure

Details

The KCA1056 Dual 5KVA Electrical Disconnect Enclosures converts 480VAC to 240VAC for powering the Knight Global servo hoists, this panel comes with an industrial flange disconnect and provides a means to lock out the system when time for maintenance. It also includes a 5KVA finger safe transformer and primary. The secondary fusing is set up for a dual output for two separate servo systems. (i.e, Knight's KSHXY, KSHXZ, KSHTCDM, and KSHXYZ Servo Tractors and Hoists). KCA1001 Electrical Disconnect Enclosure Stand Not Included.

Previously EBA1086

Used with: KSHXY, KSHXZ, KSHTCDM, and KSHXYZ Servo Tractors and Hoists.
Flange disconnect.
Provides disconnect point for two Knight Global systems.
Transformer Disconnect, Dual 5KVA.
Enclosure Size: 30 in. X 25 in. X 12 in.
480VAC – 240VAC, FLA 10.4.
25A Primary Fusing.
(2) 25A Secondary Fusing Sets.
Enclosures are mounted at a ergonomically correct height.
Optional Dual Enclosure Configuration. (Front and Back)
Stand not included.

I-Beam Column Mount Kit for Disconnect Boxes KCA1100

KCA1100I-Beam Column Mount Kit for Disconnect Boxes

Details

The KCA1100 I-Beam Column Mount Kit is designed as a universal solution for mounting Knight's Electrical disconnect boxes. It is ideal in cases where mounting options for the boxes are limited due to spatial restrictions. The Column Mount Kit can be mounted directly to an I-Beam post in multiple orientations. It does not require any drilling into posts, but instead includes beam clamps.

Mounts directly to an I-Beam Post in multiple orientations.
Works with the KCA1018, KCA1019, and KCA1056 Disconnect Boxes.
No drilling into I-Beam required.
Disconnect boxes not included.

Electrical Disconnect Enclosure Stand KCA1102

KCA1102Electrical Disconnect Enclosure Stand

Details

The KCA1102 Electrical Disconnect Enclosure Stand is for the mounting of disconnect enclosures to provide an ergonomically positioned height for the flange disconnect handle. Stand allows for multiple adjustment heights. Mounting patterns set up for Knight's KCA1019 transformer disconnect enclosure box. Electrical Disconnect Enclosure Box Not Included.